强制高潮18xxxxhd日韩,久久精品无码av,国产精品久久日日苍井空,欧美黑人疯狂性受xxxxx喷水

產品展示
首頁 > 產品展示 > > 其他檢測儀器 > TC-500 氧氮聯合測定儀

TC-500 氧氮聯合測定儀

簡要描述：簡單說明：TC500系列儀器質量、性能、工藝滿足您對金屬、難熔物、其他無機材料日常生產中氮/氧分析的需要

  • 產品型號：TC-500
  • 廠商性質：生產廠家
  • 更新時間：2024-10-08
  • 訪  問  量：1820
詳情介紹

詳細說明:

TC500系列儀器質量、性能、工藝滿足您對金屬、難熔物、其他無機材料日常生產中氮/氧分析的需要

Determination of Oxygen and Nitrogen in
Reactive/Refractory Metals and Their Alloys*
 
Approval
ASTM E-1409 Oxygen Determination in Titanium and Titanium Alloys
ASTM E-1569 Oxygen Determination in Tantalum
ASTM E-1937 Nitrogen Determination in Titanium and Titanium Alloys
 
Sample Preparation
A clean representative sample is required in order to obtain optimum results. Solid samples can be leached in suitable acid or abraded with a clean file, rinsed in acetone, and dried with warm air. Refer to ASTM methods above for further details.
 
Accessories
782-720 Crucible; 782-721 Electrode Tip; 502-344 UHP Nickel
Baskets; 501-073 Graphite; 503-032 Glass Accelerator Scoop;
501-059 Tin Capsules—for powdered samples. （Additional steps required for powdered samples are noted in parenthesis.）
 
Calibration Standard
LECO 501-320 Titanium Pin, 502-047 Zirconium Pin, NIST, or other suitable reactive/refractory metal standard.
 
Method Parameters
Analysis Parameters
Outgas Cycles                           2
Analysis Delay （seconds）             20
Analysis Comparator                 1
Analysis Type                              Auto
 
Element Parameters                  Oxygen           Nitrogen
Minimum Time （seconds）
35
55
Integration Delay （seconds）
5
15
Comparator Level （%）
1
1
 
Furnace Parameters
Furnace Control Mode             Power
Purge Time （seconds）                    15
Outgas Time （seconds）                20
Cool Time （seconds）                    5
Outgas Power （Watts）                 6300
Analyze Power （Watts）                5300
 
 
 
 
 


 

*This includes Ti, Zr, W, Mo, Ta, Nb, Hf, and their alloys.

 
TC500


 

 
Typical Results
 
 
 
Titanium Pin
Mass （g）
Oxygen （%）
Nitrogen （%）
 
0.1135
0.1808
0.0189
 
0.1133
0.1843
0.0194
 
0.1134
0.1831
0.0184
 
0.1138
0.1819
0.0188
 
0.1133
0.1821
0.0195
 
0.1131
0.1829
0.0185
 
0.1134
0.1833
0.0191
 
0.1143
0.1849
0.0194
 
0.1125
0.1837
0.0189
 
0.1072
0.1830
0.0191
 
Average
0.1830
0.0190
 
Std. Dev.
0.0012
0.0004
 
Zirconium Wire
 
Mass （g）
 
Oxygen （%）
 
Nitrogen （%）
 
0.1067
0.1246
0.0017
 
0.0978
0.1273
0.0017
 
0.1180
0.1246
0.0019
 
0.1097
0.1235
0.0014
 
0.1141
0.1272
0.0017
 
0.1017
0.1226
0.0018
 
0.1140
0.1269
0.0020
 
0.0987
0.1239
0.0020
 
0.1015
0.1233
0.0022
 
0.1197
0.1270
0.0020
 
Average
0.1251
0.0018
 
Std. Dev.
0.0018
0.0002
 
Procedure
 
 
 
1.   Determine the blank as follows:
a.   Enter the "blank" ID code with a 1.0000 g weight in the weight stack.
b.   Press the loader control switch, the sample loader will open.
c.   Place one 502-344 UHP Nickel basket into the loading head using clean tweezers.
（Place a 501-059 Tin capsule into the Nickel basket before placing it in the loading head.）
d.   Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.
e.   Remove crucible from electrode tip and discard.  Clean furnace area using the appropriate brushes.  Vacuum away loose dust.
f.    Place ~0.05 g 501-073 into the bottom of a 782-720 crucible.  ~0.05 g is approximay a ¼ full
503-032 glass accelerator scoop.
g.   Place the crucible on the lower electrode.
h.   Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.
i.    Repeat steps 1a through 1h at least four more times.
j.    Enter blank following routine outlined in operator's instruction manual.
2.   Calibrate the instrument as follows:
a.   Weigh the calibration sample. （Weigh the calibration sample into the tin capsule.）
b.   Enter the calibration sample ID code and sample weight in the weight stack.
c.   Place the calibration sample （capsule） into a nickel basket.
d.   Press the loader control switch, the sample loader will open.
e.   Carefully place the calibration sample/nickel basket （capsule） into the loading head using clean tweezers.  Make sure that the calibration sample （capsule） stays in the basket and the basket
stays upright.
f.    Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.
continued on page 3


 

Procedure （continued from page 2）
g.   Remove crucible from electrode tip and discard.  Clean furnace area using the appropriate brushes.  Vacuum away loose dust.
h.   Place ~0.05 g graphite into the bottom of a crucible.
i.    Place the crucible on the lower electrode.
j.    Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.
k.   Repeat steps 2a through 2j a minimum of three times.
l.    Complete a calibration by following the auto calibration procedure as outlined in the operator's instruction manual.
m.  Verify the calibration by analyzing the calibration sample again.  It should fall within the expected tolerances.  If not, repeat steps 2a through 2l again.
3.   Analyze the samples as follows:
a.   Weigh ~0.1 g sample. （Weigh the sample into the tin capsule.）
b.   Enter the sample ID code and sample weight in the weight stack.
c.   Place the sample （capsule） into a nickel basket.
d.   Press the loader control switch, the sample loader will open.
e.   Carefully place the sample/nickel basket （capsule） into the loading head using clean tweezers.
Make sure that the sample （capsule） stays in the basket and the basket stays upright.
f.    Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.
g.   Remove crucible from electrode tip and discard.  Clean furnace area using the appropriate brushes.  Vacuum away loose dust.
h.   Place ~0.05 g graphite into the bottom of a crucible.
i.    Place the crucible on the lower electrode.
j.    Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.
 
Theory of Operation
The TC500 is a microprocessor-based, software-controlled instrument that measures both nitrogen and oxygen in a wide variety of metals, refractories, and inorganic materials. The inert gas fusion principle is employed. A weighed sample, placed in a high-purity graphite crucible, is fused under a flowing helium gas stream at temperatures sufficient to release oxygen, nitrogen, and hydrogen. The oxygen in the
sample, combines with the carbon from the crucible to form carbon monoxide. The nitrogen present in
the sample releases as molecular nitrogen, and any hydrogen present is released as hydrogen gas. The helium carries the sample gases through heated rare earth copper oxide which converts carbon
monoxide to carbon dioxide （CO2） and hydrogen to water （H2O）. The nitrogen passes through
unchanged. The gases are then passed through a CO2  infrared （IR） cell where the oxygen is measured as
CO2. CO2  and H2O are then removed by a Lecosorb/Anhydrone trap, while the nitrogen passes through
to a thermal conductivity （TC） cell for determination.


 

TC500 Flow Diagram
 
 
 
 
 

留言框

  • 產品：

  • 您的單位：

  • 您的姓名：

  • 聯系電話：

  • 常用郵箱：

  • 省份：

  • 詳細地址：

  • 補充說明：

  • 驗證碼：

    請輸入計算結果（填寫阿拉伯?dāng)?shù)字），如：三加四=7

技術支持：化工儀器網   sitemap.xml   管理登陸
©2025 版權所有：寧波市鄞州瑾瑞儀器設備有限公司   備案號：浙ICP備14028217號-3

浙公網安備33020402000311號
欧美精品久久久久久久自慰| 国产精品久久人妻拍拍水牛影视 | 999zyz玖玖资源站永久无码| 熟妇激情内射com| 中文字幕久精品免费视频| 被黑人猛躁10次高潮视频| 伊人色啪啪天天综合婷婷| 久久国产欧美日韩精品| 中文字幕熟妇人妻在线视频| 人妻无码熟妇乱又伦精品视频 | 国产51麻豆二区精品av视频| 成年无码av片在线| 亚洲b2b网站| 三级国产三级在线| 国产又黄又大又粗视频| 色欲久久久天天天综合网| 亚洲精品中文字幕乱码三区| 99久久久无码国产精品| 麻豆MD传媒MD0049入口| 国产精品高清一区二区三区不卡| 白嫩日本少妇做爰| 国产98色在线 | 国产| 国产98色在线 | 国| 国产未成女younv仙踪林| 九月婷婷人人澡人人添人人爽| 久久久久久无码大片a片| 亚洲综合AV一区二区三区不卡| 精品久久久久久中文字幕大豆网| 中文字幕人妻中文av不卡专区| 影音先锋人妻啪啪av资源网站| 精品久久久久久中文字幕无码软件| 婷婷五月综合缴情在线视频| 实拍各种胸走光见奶头| 欧美日韩在线视频| 丁香花在线视频完整版| 色欲一区二区三区精品a片| 俄罗斯丰满熟妇hd| 国产裸体舞一区二区三区| 久久精品麻豆日日躁夜夜躁| 久久66热人妻偷产精品9| 亚洲av无码一区二区三区观看|